88227956-59
[email protected]
عضویت و ورود کاربران
تراشه ارتباطات هوشمندلیگوویو ایران
وبسایت های ما
Facebook
LinkedIn
Instagram
Skype
لیگوویو ایران | LigoWave IRAN | مهندسی تراشه ارتباطات هوشمند تنها نماینده رسمی و انحصاری فروش و خدمات پس از فروش محصولات لیگوویو در ایرانلیگوویو ایران | LigoWave IRAN | مهندسی تراشه ارتباطات هوشمند تنها نماینده رسمی و انحصاری فروش و خدمات پس از فروش محصولات لیگوویو در ایران
0
محصول با موفقیت به سبد خرید شما اضافه شد
  • صفحه اصلی
  • گروه محصولات
    • LigoDLB Series
    • LigoPTP
    • LigoPTMP
    • LigoDLBac
    • Infinity Series
    • Accessories
    • Software
  • دوره ها
    • دوره های آموزشی
      • دوره های آموزشی
      • پروفایل کاربری
      • درخواست برای مدرس شدن
    • اخبار و اطلاع رسانی
      • انجمن و تالار گفتگو لیگوویو ایران
      • آموزش | WiKi
  • لیگوویو ایران
    • درباره ما
      • راهکارهای لیگوویو | Solutions
      • دانلودها | Downloads
      • کنترلر ابری لیگوویو
    • خدمات ما
      • امکان سنجی
      • ویدئوهای آموزشی لیگوویو
      • دوره های آموزشی
        • دوره های آموزشی
        • حساب کاربری
        • درخواست برای مدرس شدن
    • تماس با ما
      • درخواست نمایندگی
      • لیست قیمت محصولات
    • پشتیبانی
      • ارسال تیکت
      • تیکت های من
      • حساب کاربری من
      • خروج
  • فروشگاه
  • تیکت پشتیبانی
    • ثبت تیکت
    • تیکت های من
  • انجمن ها

LigoPTP Installation Recommendations

خانه ٌآموزش | WiKi LigoPTP Installation Recommendations
Improving Link Stability and Throughput in Noisy Environments
Link Installation Recommendations
Improving Link Stability and Throughput in Noisy Environments

There are several solutions that users can implement, if a link is not working well.

۱٫ Set the Channel width to the lowest available value.

۲٫ Gradually reduce the Max data rate one step at a time (from 300 to 240, then to 180, etc.).

۳٫ Make sure that Dynamic rate is enabled.

۴٫ Set Transmit queue length to 32.

The aforementioned changes can be performed in Configuration > Radio on the Master device.

If these solutions do not fix the problem, the problem may lie in the fact that the current channel has too many other Access Points (APs). To look for a better channel, navigate to Tools > Spectrum Analyzer and click Start. Wait 20–۳۰ seconds while the radio gathers enough packets to provide real time noise data.

If the Spectrum Analyzer is running, link connection is lost until the Stop button is clicked.

ligospectrumamalyzer

If the device’s current operating channel is overcrowded, as shown by the high noise bars in the above picture, look for a frequency range where noise bars are the lowest. The above example shows that the frequency ranges with the least amount of noise are 5,340–۵,۳۸۰MHz and 5,430–۵,۴۷۰MHz.

To find the right channel and to avoid collision with other APs, perform a scan in Tools > Site survey.

linkimprovsitesurvey

Choose a frequency that does not match the frequency indicated in the Site Survey’s Frequency column and which is within a clean frequency range. Then set it up on the Master device (Configuration > Radio).

Also, try to avoid frequencies with other devices working on adjacent frequencies. For example, the illustration provided above shows that the 5,430MHz frequency does not have any devices operating on it. However, there are devices operating nearby on 5,400MHz and 5,460MHz, which can cause interference, especially of the idea is to use 40MHz channels.

The channels available may vary depending on the selected country code.

Once a link is set up, use the LinkTest tool to verify the W-Jet frames data rate and the overall capacity of the link. If the results are not good enough, try another channel or decrease the maximum data rate. If the speed is sufficiently good, try to move the current frequency up or down by 5MHz and check if throughput improves even more.

ligoWjet

Link Installation Recommendations
Link Installation Recommendations

Link aggregation configuration can be found here.

Follow these rules to achieve maximum performance using link aggregation:

۱٫ If the devices are using integrated antennas, mount the devices at least 2 meters apart from each other. The farther—the better.

۲٫ If the devices are using dish antennas, mount the dishes at least 0.5 meters apart from each other. The farther—the better.

۳٫ Use different channels on Unity and PRO devices. Channels should be separated by at least 100MHz. Ideally—۳۰۰MHz.

LigoPTP Unity + PRO Mounting Recommendations

AtstumaiPTP-2

Mounting Recommendations for LigoPTP Unity + PRO with External Antennas
AtstumaiPTPantenos-2
Standard LigoPTP Unity + PRO Setup

PTPjungimas2-1

LigoPTP Unity + PRO Setup Using PoE Switches
Important! Switch ports 5 and 6 must be configured as access ports in separated/isolated VLAN X. Other ports can be set to default VLAN 1.

PTPjungimas1-1

 LigoPTP Unity + Unity Setup Scheme
Follow the LigoPTP Unity + PRO installation recommendations to keep the recommended distances between devices.

PTP UNITY@jungimas2-11

ورود به سایت

ثبت نام
رمز عبور خود را فراموش کردید؟

با ما در شبکه های اجتماعی

Email
Facebook
LinkedIn
Instagram
Skype

جستجو در سایت

آدرس :تهران، تقاطع خیابان ولیعصر و طالقانی، مجتمع نور تهران، طبقه 10 اداری، واحد 2210

[email protected]

88227956-59

داخلی 6

  • صفحه اصلی
  • درباره ما
  • ٌآموزش
  • اخبار
  • فروشگاه
  • تماس با ما
تمامی حقوق مادی و معنوی این سایت متعلق به شرکت تراشه ارتباطات هوشمند می باشد.Copy Right @2021